PANDUIT: Electrical Full Line

mm In. mm In. mm In. N Lbs. m Ft. mm In. Std. Pkg. Qty. ‡ Recommended Banding Head Recommended Installation Tool*** Thickness ^ Width Min. Bundle Diameter Min. Loop Tensile Strength ** Length * Max. Bundle Diameter Part Number For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) ELECTRICAL SOLUTIONS B3.13 B2. Cable Accessories C1. Wiring Duct C3. Abrasion Protection C4. Cable Management D1. Terminals D2. Power Connectors E1. Labeling Systems E2. Labels E3. Pre-Printed & Write-On Markers F. Index B3. Stainless Steel Ties C2. Surface Raceway E5. Lockout/ Tagout & Safety Solutions B1. Cable Ties A. System Overview D3. Grounding Connectors E4. Permanent Identification To determine the proper amount of banding required, use the following formula: Calculate S and H Cross Section Diameter inches (mm) x 3.14 + 3 inches (76mm) Calculate EH and SH Cross Section Diameter inches (mm) x 3.14 + 4.5 inches (114mm) Pan-Steel ® Custom Length Banding Heads – MTH Series • Self-locking head design speeds installation and locks into place at any length along the tie body Part Number Part Description Std. Pkg. Qty. Std. Ctn. Qty. AISI 304 Stainless Steel MTHS-C Loose piece banding head for standard cross section banding. 100 1000 MTHH-C Loose piece banding head for heavy cross section banding. 100 1000 MTHEH-C Loose piece banding head for extra-heavy cross section banding. 100 1000 MTHSH-C Loose piece banding head for super-heavy cross section banding. 100 1000 AISI 316 Stainless Steel MTHS-C316 Loose piece banding head for standard cross section banding. 100 1000 MTHH-C316 Loose piece banding head for heavy cross section banding. 100 1000 MTHEH-C316 Loose piece banding head for extra-heavy cross section banding. 100 1000 MTHSH-C316 Loose piece banding head for super-heavy cross section banding. 100 1000 AISI 316 Coated Stainless Steel MTHCH-C316 Loose piece coated banding head for heavy cross section banding. 100 1000 MTHCEH-C316 Loose piece coated banding head for extra-heavy cross section banding. 100 1000 MTHCSH-C316 Loose piece coated banding head for super-heavy cross section banding. 100 1000 1) Take one end of the cut banding and bend back 1/2" (13mm). 2) Take a self-locking head and slide it the entire length of the band until it reaches the bend. 3) Bend tail flat against bottom of banding head to complete assembly. Pan-Steel ® Custom Length Banding – MBS, MBH, MBEH and MBSH Series *Other lengths available, contact Panduit Customer Service. **Per SAE Standard AS23190/3 (formerly MIL). For additional details, refer to page B3.32. ***For information on installation tools, refer to pages B3.14 – B3.16. ^Base material less coating ‡Order in number of reels required. Polyester Coated AISI 316 Stainless Steel Heavy Cross Section MBCH-QR316 Any Any 82 25 250 1112 0.50 12.7 0.31 7.9 0.010 0.25 GS4MT, ST2MT, HTMT, PPTMT, PBTMT MTHCH-C316 1 Extra-Heavy Cross Section MBCEH-QR316 Any Any 82 25 300 1335 1.00 25.4 0.50 12.7 0.010 0.25 ST2MT, RT2HT, RT2HTN, PBTMT MTHCEH-C316 1 Super-Heavy Cross Section MBCSH-QR316 Any Any 82 25 450 2000 1.00 25.4 0.63 15.9 0.015 0.38 RT2HT, RT2HTN, PBTMT MTHCSH-C316 1