PANDUIT: Electrical Full Line

ELECTRICAL SOLUTIONS B1.102 B2. Cable Accessories C1. Wiring Duct C3. Abrasion Protection C4. Cable Management D1. Terminals D2. Power Connectors E1. Labeling Systems E2. Labels E3. Pre-Printed & Write-On Markers F. Index B3. Stainless Steel Ties C2. Surface Raceway E5. Lockout/ Tagout & Safety Solutions B1. Cable Ties A. System Overview D3. Grounding Connectors E4. Permanent Identification ASTM D 635 Samples of a material, with dimensions 125mm by 12.5mm and the thickness of the intended end use product, are tested in an unaged “as manufactured” state. A precisely controlled flame is applied to the specimen and a stopwatch is started. The flame is applied for 30 seconds. The stopwatch is stopped when burning or glowing combustion ceases or when the flame has proceeded to a mark 100mm from the free end. Ten specimens are tested. If any of the specimens burn to the 100mm mark, an additional ten specimens are tested. Burning Rate • If two or more specimens have burned to the 100mm mark then Average Burning Rate (cm/min.) shall be reported as the average of the burning rates of all specimens which have burned to the 100mm mark Table B – Flammability Ratings ■ TEFZEL is a registered trademark of E.I. du Pont de Nemours and Company. ▲ HALAR is a registered trademark of Ausimont USA, Inc. AEB, mm = [10(mm) – unburned length(mm)] N = Number of specimens tested Rounded to the nearest 5mm N = Number of specimens tested Rounded to the nearest 5 seconds Flammability (continued) N 0 N ATB, s = [time(sec) – 30(sec)] N Σ N 0 Σ *UL Recognized cable ties meet stated ratings. **UL Recognized -0 parts Average Time of Burning and Average Extent of Burning • Average time of burning and average extent of burning of the sample shall be reported if none of the ten samples or no more than one of the twenty specimens have burned to the 100mm mark • Average Time of Burning (ATB): • Average Extent of Burning (AEB): UL 94 94V-2 @ .71mm 94V-2 @ .71mm 94V-2** @ .71mm 94V-2 @ .71mm 94V-2 @ .71mm 94V-2 @ .71mm 94V-0 @ .81mm 94V-0 @ .81mm 94V-0 @ 1.5mm 94 HB @ .71mm 94 HB @ 1.6mm 94 HB @ .94mm 94 HB @ .94mm 94V-0 @ 1.5mm 94V-0 @ .18mm 94 HB @ 1.5mm Materials Nylon 6.6, Natural Weather Resistant Nylon 6.6, Black (Meets Mil. Spec.) Weather Resistant Nylon 6.6, Black* Heat Stabilized Nylon 6.6, Black Heat Stabilized Nylon 6.6, Natural Heat Stabilized Weather Resistant Nylon 6.6, Black Flame Retardant Nylon 6.6, Black Flame Retardant Nylon 6.6, Natural (Ivory) PEEK, Polyetheretherketone, Translucent Brown Metal Detectable Nylon 6.6, Blue Weather Resistant Nylon 12, Black Polypropylene, Green Weather Resistant Polypropylene, Black TEFZEL ■ , Aqua Blue HALAR ▲ , Maroon Weather Resistant Acetal, Black ASTM D 635 AEB = 20mm ATB = 5 seconds AEB = 20mm ATB = 5 seconds AEB = 20mm ATB = 5 seconds AEB = 20mm ATB = 5 seconds AEB = 20mm ATB = 5 seconds AEB = 20mm ATB = 5 seconds AEB = 15mm ATB = < 5 seconds AEB = 15mm ATB = < 5 seconds — AEB = 20mm ATB = 5 seconds Avg. Burning Rate 1.6cm/min. Avg. Burning Rate 2cm/min. Avg. Burning Rate 2cm/min. AEB = 15mm ATB = < 5 seconds AEB = 15mm ATB = < 5 seconds Avg. Burning Rate 2.8cm/min Part Number Suffix None 00 0 30 39 300 60 69 71 86 120 109 100 76 702Y DT Prefix